Developed with a concerted focus on the attenuation of vibration, to generate and increase the quantity of kinetic energy produced and transferred from the golf swing into the clubhead. KINETIXX® loaded golf shafts are the world's most concentric and precisely tailored composites. Designed to optimize performance of todays clubheads. available in shafts for all categories, driver, Fairway, Hybrid and Iron. KINETIXX® loaded shaft technologies are the world's most advanced array of demonstrably unique, visibly tailored, precision crafted, swing interactive golf shaft technologies to enter the market.

PADERSON® KINETIXX® loaded shafts, are the genuine confluence of materials and craftsmanship. Featuring the world's only pre-loaded vacuum cured, table rolled and visible fiber structural technologies.

The visible rhombus grid in all KINETIXX® IMRT loaded shafts, is the structural architecture that influences EI, Torque, Dynamic flex, Recovery, Feel and most important, attenuation of vibration for the purest kinetic energy transfer from golfer to club. Maximizing swing efficiency, optimizing clubhead performance.

Our patented and proprietary methods of manufacture enable us to pre-load all fibers to a preordained tension, according to each flex.

KINETIXX® loaded shafts, combine one of our three signature construction platforms. putting to practise, filament winding and table rolling methods, independently and or Combined (depending on the KINETIXX® model) to produce one homogenous structure.

Our proprietary vacuum curing process Minimizes resin, to Maximize the Fiber Area Weight to resin ratio. this is essential, regardless of material and modulus to optimizing fiber performance, in terms of responsiveness and the capacity to store and deliver energy at the critical moment of impact.

Producing the world's only golf shafts tailored to increase in frequency the greater the force applied. to the benefit of down range performance: increasing ball speed and reducing shot dispersion.

Our extraordinary multi-process construction methods, allow for use of the materials that present unlimited combinations of torque, flexibility, weight, and balance. enabling us to produce shafts that fit every golfer's swing.

Sophisticated by design, yet simple to fit.

THE REVOLUTIONARY KINETIXX® IMRT (Impedance Matched Response Technology), and KINETIXX® VMT (Velocity Multiplier Technology) product line up is as follows:


1. Filament wound Vacuum Cured Construction,wound = round concentric golf shafts,with no spine! unparalleled consistency, as compared with all conventional table rolled prepreg, (regardless of modulus) or steel shafts..



DOWN RANGE PERFORMANCE BENEFIT: Increased Flight Distance with tighter shot Dispersion, as a function of increasing Ball Speed and reducing spin, with todays conventional high performance clubhead systems.

Balanced strength in the butt and tip quadrants. KINETIXX® IMRT loaded continuous fiber filament wound shafts produce incomparable stability, dynamic response and feedback. Fitting the widest array of players and swing types; short, medium, full and long backswings, narrow to wide arcs, hitter and swinger profiles, fast or slow transition speeds and tempo!

KINETIXX® IMRT continuous fiber filament wound golf shafts, feature the world's only pre-loaded visible fiber structural technology. Fiber architecture and tension tailored according to flex, insures all shaft flexes of proportionately similar high order magnitude attenuation of vibration, for the purest kinetic energy transfer from golfer to club..

preordained vibration suppression, vibration control from butt-Tip. the confluence of materials and craftsmanship featured in all KEVLAR GREEN KINETIXX® IMRT branded Driver, Fairway, Hybrid & Iron Shafts; KEVLAR BLUE KINETIXX® IMRT branded Hybrid & Iron shafts; Ni KINETIXX® IMRT branded Limited Edition NiCKEL Driver & Iron Shafts, are all truly a milestone breakthrough!

The KINETIXX® loaded IMRT KEVLAR series presents an incomparable technical value proposition. Featuring the world's only continuous fiber filament wound braided kevlar fiber material application. Kevlar offers an incredibly high tensile strength-to-weight ratio. by this measure it is 5x stronger than steel, with 20x the elastic strength.

Yet Kevlar has no modulus, therefore combined with the limitations in the manufacturing methods practiced by all conventional shaft manufacturers, the workable form factor of their Kevlar and related applications are limited to high density, ineffective pre- impregnated sheet or liquid crystal polymer.

In fact, materials like Zylon and coatings like LCP (Liquid Crystal Polymer) are both diminutives of kevlar, present merely in as part of the atomic branch chain of elements that comprise global atomic structure, that is kevlar. therefore due to mass and design constraints in golf shaft applications, kevlar either in sheet or partial form as in LCP, is incapable of realizing any elastic strength and dynamic property benefits of the entire kevlar chain, inherent in all paderson® KINETIXX® IMRT loaded continuous fiber filament wound KEVLAR shaft applications. Now available in shafts, driver through iron.

*see fit tab for further guidance in shaft selection.


2. FILAMENT WOUND WITH TABLE ROLLED CONSTRUCTION fused and pre-loaded fiber tension according to flex through Vacuum Curing:


DOWN RANGE PERFORMANCE BENEFIT: Increased Distance with Reduced Dispersion as a function of generating clubhead speed and Powering an Increased Clubhead launch Angle and center to draw shot bias, with todays lower spin club head systems.

KINETIXX® IMRT signature vibration control technology visibly loaded in the concentric continuous fiber filament wound butt-mid quadrant, tailored attenuation of vibration for the purest kinetic energy transfer from golfer to club transferred from butt to tip at the moment of impact. isolating the deflection mode, to the lower half and tip quadrant

The visible BLUE KEVLAR & 3K fiber rhombus filament wound grid in the butt quadrant produces a higher balance point and inertially tailored shaft with the potential for lighter swing weight. preordaining this series with the dynamic ability to generate increases in head speed, launch angle and produce a center, to draw shot bias with todays conventional high performance clubhead systems.

This is a multi-structure multi-material multi-process composite. Featuring a stiff, concentric wound butt-mid Quadrant and a smooth proportionately softer (flex dependent) reactive high modulus mid-tip quadrant table rolled structure. The wound and rolled structures are fused and pre-loaded to tension through vacuum curing. Producing one homogenous dynamically tailored composite structure. 

*see fit tab for further guidance in shaft selection.

3. Table Rolled Vacuum Cured Construction, minimizing resin to maximize the dynamic recovery properties, tension, feedback and consistency in a table rolled composite!

KINETIXx® VMT loaded driver and long driver shafts, SOFT IN THE HANDS, ACTIVE IN THE HEAD..featuring, our patented dual flex point, reactive shaft technology.

DOWN RANGE PERFORMANCE BENEFIT: Increased Distance with Reduced Dispersion, as a function of increasing Ball Speed and lowering Clubhead Spin through the attenuation of rogue vibration modes inherent to prepreg table rolled composite shafts, for the purest kinetic energy transfer from golfer to club.

This is the only full table rolled construction in the KINETIXX® loaded cache. KINETIXX® VMT features the world's only pre-loaded, table rolled vacuum cured nano-technology, amorphous fiber material application, in a golf shaft.

Giving this shaft the distinction of having the lowest and most consistent resin fiber coverage and highest F.A.W., Fiber Area Weight ratio of any table rolled composite shaft on the market today. Delivering exceptional feel, stability and consistency. Contributing to clubhead performance specific to increasing ball speed and reducing spin in todays low spin drivers of conventional playing lengths as well as in long driver set-ups with playing lengths >48.00" at high swing speed velocity.

KINETIXX® VMT (Velocity Multiplier Technology) features signature vibration control technology to the benefit of club speed and ball velocity.

The active butt and tip quadrants are tailored to a progressively Stiff-X-Stiff middle quadrant that works as a reaction mass, Precisely located and tailored to recover the tip quadrant at the moment of impact, as a function of time and force, according to each flex. Producing an extremely Hard kicking lower half and tip, for increased ball speeds.

Vacuum curing produces incomparable consistency, as never before achieved in a standard prepreg table rolled composite, combined with a smooth, extraordinarily stable bending profile.

*see fit tab for further guidance in shaft selection.